Tripp Lite RGB Component Video + Audio Over Cat5 Cat6 IP Extender Receiver TAA 1080i - 1 Output Device - 328.08 ft Range - 1 x Network (RJ-45) - WUXGA - 1920 x 1200 - Twisted Pair - Category 6 - Rack-mountable - TAA Compliant - TAA Compliance B160-100-CSI

Tripp Lite RGB Component Video + Audio Over Cat5 Cat6 IP Extender Receiver TAA 1080i - 1 Output Device - 328.08 ft Range - 1 x Network (RJ-45) - WUXGA - 1920 x 1200 - Twisted Pair - Category 6 - Rack-mountable - TAA Compliant - TAA Compliance

The B160-100-CSI RGB Component Video + Audio over IP Extender Receiver works with a Tripp Lite B160-Series transmitter (sold separately) to extend and distribute component video + stereo audio, RS-232 serial and IR (infrared) remote signals from the source to the display located up to 328 feet (100 meters) away, which is more than 200 feet farther than a traditional Cat5e/6 solution. By adding a chain of low-cost unmanaged network switches, such as Tripp Lite''s NG5, you can continue extending the distance between source and display up to 328 feet per switch.Create a multi-in, multi-out installation with up to 64 transmitters and 255 receivers by connecting dedicated managed Ethernet network switches with Internet Group Management Protocol (IGMP), such as Tripp Lite''s NSS-G16D2. With a compatible B160-Series transmitter, this receiver works with any analog or digital source, including HDMI, VGA and DisplayPort™, allowing you to mix and match technologies and use existing source devices. An IGMP-enabled switch will let you manage all connections for centralized control over which sources show on which displays.The B160-100-CSI supports video resolutions up to 1080i. It extends IR control signals that control a source, such as a Blu-ray™ player, from a remote display, as well as RS-232 signals at serial baud rates up to 57600 Bps. It mounts to a wall, rack or pole using the included hardware. Features RGB Component Video + Stereo Audio, Serial and IR Control Signals over Cat5/6 Cabling Receives IP-based audio + video transmitted point-to-point from a source 328 ft. away Add low-cost network switches between transmitter and receiver to continue extending distance up to 328 ft. per switch Create a Multi-In, Multi-Out Installation Using B160-Series Transmitters and Receivers Connect up to 64 transmitters and 255 receivers through multiple dedicated managed network switches IGMP-enabled switches allow centralized control over which sources show on which displays Displays video from any analog or digital source, so you can mix and match technologies and use existing sources and monitors Enhanced Technical Features Supports video resolutions up to 1080i Uses H.264 video compression standard Transmits on 20-60 kHz IR frequency Extends IR control signals that control a source from a remote display Supports RS-232 serial baud rates up to 57600 Bps Plug-and-Play Functionality No software or drivers required Hardware included for mounting on wall, rack or pole Compatible with all Tripp Lite B160-Series A/V over IP transmitters TAA-Compliant Compliant with the Federal Trade Agreements Act (TAA) for GSA Schedule purchases

Technical Specifications:
Connectivity Technology: Wired
Number of Output Devices Supported: 1
Maximum Operating Distance: 328.08 ft
Graphics Modes: WUXGA
Maximum Video Resolution: 1920 x 1200
Network (RJ-45): Yes
Number of Network (RJ-45) Ports: 1
Media Type Supported: Twisted Pair
Twisted Pair Cable Standard: Category 6
Product Color: Black
Receiver Height: 1.17"
Receiver Width: 5.04"
Receiver Depth: 3.94"
Form Factor: Rack-mountable
Receiver Weight (Approximate): 1.59 lb
Package Contents:

Receiver Unit, External Power Supply (Input: 100-240v, 50/60 hz, 0.5a; Output: 5v 2A), Plug Adapters for U.S., U.K., Europe and Australia, IR-In Cable, 3.5 mm to db9 Adapter Cable (m/m), Mounting Hardware, Owner's Manual

Environmentally Friendly: Yes
Environmental Certification: RoHS
Country of Origin: Taiwan
TAA Compliant: Yes

Write a review

Your Name:


Your Review: Note: HTML is not translated!

Rating: Bad           Good

Enter the code in the box below: